http://skysense.co/blog/2015/01/ces-2015
aaron
About this project INTRODUCTION The IR-LOCK Sensor system is used to autonomously land copters in small areas. Simply place the MarkOne Beacon at the desired landing point, and initiate the LAND mode. This is useful for docking with charging stations, package delivery systems, UAV-to-ground vehicle interaction, etc. The MarkOne Beacon [...]
Guided precision landing
I modified this way back, adding some extra strength to the part and leveling out the area that mates to the bed. If you have been using this setup this is a great way to add some stability. The rods have been moved the the outermost edges of the part, [...]
1405 JONBOT print bed ends reenforced Widened rods by danman1178
No sag/Extended Y-Axis: http://www.thingiverse.com/thing:372467 X Ends: http://www.thingiverse.com/thing:376515 http://www.thingiverse.com/thing:377357/#files Z Axis: Printrbot Z Axis 5mm threaded rod upgrade by RedJoe I was unhappy with the 5/16 threaded rod that the Printrbot comes with and the Z-ribbing artifacts. The problem is the stepper motors have an uneven amount of steps with the [...]
3D printer upgrades for printrbot 1405 simple makers kit.
Source: Customizable Temp Calibration Tower (fixed!) by eibwen
Customizable Temp Calibration Tower (fixed!) by eibwen
This mod adds a third linear rod in both the Y and Z axes. The third rod greatly reduces the amount of twisting that can occur, especially with an extended Y mod installed. This mod is based off of Jon Lawrence’s 300mm no sag mod. It also includes modifications to [...]
Printrbot Simple 1405 “TRI ROD MOD” with or without XL ...
I was unhappy with the 5/16 threaded rod that the Printrbot comes with and the Z-ribbing artifacts. The problem is the stepper motors have an uneven amount of steps with the 5/16 rod. When you print something with the 5/16 rod, your layer heights will be off every x number [...]
Printrbot Z Axis 5mm threaded rod upgrade by RedJoe
This was my first try in 3D modeling something for posterior printing. If you print it, please reply with the result! It’s just a simple Sunshade for iPad air divided in 2 pieces to use in Phantom 3 Remote. Enjoy Source: iPad Air Phantom 3 Drone SunShade (2 Pieces) – [...]
iPad Air Phantom 3 Drone SunShade (2 Pieces) – 1st ...
I cut my sunshade design out of hard carton and taped it together with some white tape. Source: Apple Ipad mini sunshade by chrisebryan
Apple Ipad mini sunshade by chrisebryan
While working on making a observation screen for people while i am FPV flying I wanted to try and make a sunscreen for the old 7 inch monitor i had left over from an old in car DVD system. i have not printed it up after i made some changes [...]
Sun Screen for my old 7 inch monitor by Lowfiero
Rigid FPV monitor support for FrSky Taranis. Source: FrSky Taranis FPV monitor holder by igi79
FrSky Taranis FPV monitor holder by igi79
Designed for the DJI Phantom 1 This mount allows you to separate your FPV transmitter away from your GPS module minimizing inference. Custom zip tie holes allow you to securely mount your video transmitter or OSD device. (The longer M3*8 extra screws that come with the phantom work well to [...]
DJI Phantom FPV / OSD mount by questpact
A simple and strong FPV LCD holder for the FrSky Taranus or Turnigy 9X. I use it for mounting my RC800, 7″ LCD display. It will also hold other LCDs with back or bottom 1/4-20 mounts. I used a DIY 3S 2000mah battery pack, made of 3 18650 LiPo cells, [...]
FPV LCD Holder by HLMAX
I made this for a customer to use his TS58500 mini 5.8GHz FPV video transmitter with his Phantom 2 (with Zenmuse 3D Gimbal). Note: You will need to make a wire to connect the video transmitter correctly (not shown). If you are not expert with these things get help. My [...]
DJI Phantom 2 FPV mount
I wanted to install a gimbal on my Phantom. So I design a 20mm raise and un battery holder. Another advantage is to rebalance the quadricopter. Source: 20mm raiser for DJI Phantom + battery holder by 3D_CC_design
20mm raiser for DJI Phantom + battery holder by 3D_CC_design
Designed for the DJI Phantom 1 This mount allows you to separate your FPV transmitter away from your GPS module minimizing inference. Custom zip tie holes allow you to securely mount your video transmitter or OSD device. (The longer M3*8 extra screws that come with the phantom work well to [...]
DJI Phantom FPV / OSD mount by questpact
Here is a 3D printed clip on screen mount for the Phantom controller use’s a GoPro type connector to make it adjustable and can be used for other things. Source: DJI Phantom Controller Mount by markloane
DJI Phantom Controller Mount by markloane
I’ve had quite a few requests for the motorized version of the hand cranked Perseverance thing (http://www.thingiverse.com/thing:348489) , so here it is, Perseverance, Motorized. It makes a unique bookend, I receive plenty of inquiries as to where I bought it ( 😉 ). I’ve also printed one using glow in [...]