aaronsworld.com

A place to share my experiences

Daily Archives: February 16, 2016

This was my first try in 3D modeling something for posterior printing. If you print it, please reply with the result! It’s just a simple Sunshade for iPad air divided in 2 pieces to use in Phantom 3 Remote. Enjoy Source: iPad Air Phantom 3 Drone SunShade (2 Pieces) – [...]

iPad Air Phantom 3 Drone SunShade (2 Pieces) – 1st ...

February 16, 2016 in 3D Printing by aaron

I cut my sunshade design out of hard carton and taped it together with some white tape. Source: Apple Ipad mini sunshade by chrisebryan

Apple Ipad mini sunshade by chrisebryan

February 16, 2016 in 3D Printing by aaron

While working on making a observation screen for people while i am FPV flying I wanted to try and make a sunscreen for the old 7 inch monitor i had left over from an old in car DVD system. i have not printed it up after i made some changes [...]

Sun Screen for my old 7 inch monitor by Lowfiero

February 16, 2016 in 3D Printing by aaron

Rigid FPV monitor support for FrSky Taranis. Source: FrSky Taranis FPV monitor holder by igi79

FrSky Taranis FPV monitor holder by igi79

February 16, 2016 in 3D Printing by aaron

Designed for the DJI Phantom 1 This mount allows you to separate your FPV transmitter away from your GPS module minimizing inference. Custom zip tie holes allow you to securely mount your video transmitter or OSD device. (The longer M3*8 extra screws that come with the phantom work well to [...]

DJI Phantom FPV / OSD mount by questpact

February 16, 2016 in 3D Printing by aaron

A simple and strong FPV LCD holder for the FrSky Taranus or Turnigy 9X. I use it for mounting my RC800, 7″ LCD display. It will also hold other LCDs with back or bottom 1/4-20 mounts. I used a DIY 3S 2000mah battery pack, made of 3 18650 LiPo cells, [...]

FPV LCD Holder by HLMAX

February 16, 2016 in 3D Printing by aaron

I made this for a customer to use his TS58500 mini 5.8GHz FPV video transmitter with his Phantom 2 (with Zenmuse 3D Gimbal). Note: You will need to make a wire to connect the video transmitter correctly (not shown). If you are not expert with these things get help. My [...]

DJI Phantom 2 FPV mount

February 16, 2016 in 3D Printing by aaron

I wanted to install a gimbal on my Phantom. So I design a 20mm raise and un battery holder. Another advantage is to rebalance the quadricopter. Source: 20mm raiser for DJI Phantom + battery holder by 3D_CC_design

20mm raiser for DJI Phantom + battery holder by 3D_CC_design

February 16, 2016 in 3D Printing by aaron

Designed for the DJI Phantom 1 This mount allows you to separate your FPV transmitter away from your GPS module minimizing inference. Custom zip tie holes allow you to securely mount your video transmitter or OSD device. (The longer M3*8 extra screws that come with the phantom work well to [...]

DJI Phantom FPV / OSD mount by questpact

February 16, 2016 in drones by aaron

Here is a 3D printed clip on screen mount for the Phantom controller use’s a GoPro type connector to make it adjustable and can be used for other things. Source: DJI Phantom Controller Mount by markloane

DJI Phantom Controller Mount by markloane

February 16, 2016 in 3D Printing by aaron

I’ve had quite a few requests for the motorized version of the hand cranked Perseverance thing (http://www.thingiverse.com/thing:348489) , so here it is, Perseverance, Motorized. It makes a unique bookend, I receive plenty of inquiries as to where I bought it ( 😉 ). I’ve also printed one using glow in [...]

Perseverance, Motorized by gzumwalt

February 16, 2016 in 3D Printing by aaron